|
Power over Ethernet or PoE technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. This technology is useful for powering IP telephones, wireless LAN access points, webcams, Ethernet hubs, computers, and other appliances where it would be inconvenient or unfeasible to supply power separately. The technology is somewhat comparable to POTS telephones, which also receive power and data (although analog) through the same cable. It works with an unmodified Ethernet cabling infrastructure. There are several general terms used to describe this feature. The terms Power over Ethernet (PoE), Power over LAN (PoL), Power on LAN (PoL), and Inline Power are synonymous terms used to describe the powering of attached devices via Ethernet ports. There are several PoE implementations, including ad-hoc techniques, but supplying power over ethernet according to the IEEE standard is strongly recommended. Currently recommended (IEEE 802.3-2005) Clause 33 of IEEE 802.3-2005 (commonly referred to as IEEE 802.3af) provides 48 volts DC over two out of four available pairs on a Cat. 3/Cat. 5 cable with a maximum current of 400 milliamperes for a maximum load power of 15.4 watts. Only about 12.95 watts are available after counting losses, and most switched power supplies will lose another 10-20% of the available energy. A "phantom" technique is used so that the powered pairs may also carry data. This permits its use not only with 10BASE-T and 100BASE-TX, which use only two of the four pairs in the cable, but also with 1000BASE-T (Gigabit Ethernet), which uses all four pairs for data transmission. This is possible because all versions of Ethernet over twisted pair cable specify differential data transmission over each pair with transformer coupling; the DC supply and load connections can be made to the transformer center-taps at each end. Each pair thus operates in "common mode" as one side of the DC supply, so two pairs are required to complete the circuit. The polarity of the DC supply is unspecified; the powered device must operate with either polarity or pair 45+78 or 12+36 with the use of a bridge rectifier. The standard describes two types of devices: Power Sourcing Equipment (PSE) and Powered Devices (PD). Power Sourcing Equipment provides power to the Powered Devices. Powering devices Two modes, A and B, are available. In mode A, pins 1-2 (pair In mode B, pins 4-5 (pair The Power sourcing equipment (PSE) decides whether power mode A or B is to be used, not the powered device (PD). The PSE can implement mode A or B or both (but must not supply power in both modes at the same time). If the PSE detects either an open or a short circuit, no power is applied, thus protecting devices that do not support IEEE 802.3af. To stay powered, the PD must continuously use 5-10 mA for at least 60 ms with no less than 400 ms since last use or else it will be unpowered by the PSE. Stages of powering up a PoE link Power levels available Under development extension (IEEE 802.3at) A future standard, commonly referred to as PoE+, is being developed by the IEEE 802.3at committee, which officially began work in September 2005. The draft standard describes extending the IEEE Power over Ethernet by using all four pairs of standard Ethernet Category 5 cable to provide up to 56 watts of power. The higher power available with this future standard should make self-powered equipment with higher power requirements such as WiMAX transmitters, pan-tilt-zoom cameras, videophones and thin clients possible. Cisco Measure returned LinkPulse, then provide 48 V DC. Requires special PHY. Filter will only couple LinkPulse not ordinary packets. Max 10 W. 3Com "EPS" (3C10220 & 3C10222 ?), Designed and Manufactured by PowerDsine, Inc (www.powerdsine.com) Measure capacitance signature, then provide -24 V DC. Homebrew Commonly just wires the spare pairs 4-5 (positive) and 7-8 (negative) to an appropriate DC power source. Issues like wire resistance and maximum current have to be calculated. In many countries there are regulations for voltages above 50 V to be considered. Example: Linksys WRT54G (12 V, 1 A) fed over 10 m Cat5 cable (AWG 24, 0.2 mm²). The cable resistance will be 0.8 Ω, the resulting voltage drop 0.8 V. As the Linksys converts the voltage to 5 V internally this drop is not critical and the installation will work fine. Notes Category 5 cable uses 24 AWG which can safely carry 800 mA at 48 V. The cable has eight wires and therefore the absolute maximum power transmitted is 48 V | |||||||
|
| ||||||||
 |
|
| |