|
Film basics There are two primary types of photographic film: In order to produce a usable image, the film needs to be exposed properly. The amount of exposure variation that a given film can tolerate while still producing an acceptable level of quality is called its exposure latitude. Color print film generally has greater exposure latitude than other types of film. Additionally, because print film must be printed to be viewed, after-the-fact corrections for imperfect exposure are possible during the printing process. The concentration of dyes or silver salts remaining on the film after development is referred to as optical density, or simply density; the optical density is proportional to the logarithm of the optical transmission coefficient of the developed film. A dark image on the negative is of higher density than a more transparent image. Most films are affected by the physics of silver grain activation (which sets a minimum amount of light required to expose a single grain) and by the statistics of random grain activation by photons. The film requires a minimum amount of light before it begins to expose, and then responds by progressive darkening over a wide dynamic range of exposure until all of the grains are exposed and the film achieves (after development) its maximum optical density. Over the active dynamic range of most films, the density of the developed film is proportional to the logarithm of the total amount of light to which the film was exposed, so the transmission coefficient of the developed film is proportional to a power of the reciprocal of the brightness of the original exposure. This is due to the statistics of grain activation: as the film becomes progressively more exposed, each incident photon is less likely to impact a still-unexposed grain, yielding the logarithmic behavior. If parts of the image are exposed heavily enough to approach the maximum density possible for a print film, then they will begin losing the ability to show tonal variations in the final print. Usually those areas will be deemed to be overexposed and will appear as featureless white on the print. Some subject matter is tolerant of very heavy exposure; brilliant light sources like a bright lightbulb, or the sun, included in the image generally appear best as a featureless white on the print. Likewise, if part of an image receives less than the beginning threshold level of exposure, which depends upon the film's sensitivity to light - or speed - the film there will have no appreciable image density, and will appear on the print as a featureless black. Some photographers use their knowledge of these limits to determine the optimum exposure for a photograph; for one example, see the Zone system. Most automatic cameras instead try to achieve a particular average density. Film speed Film speed describes a film's threshold sensitivity to light. The international standard for rating film speed is the ISO scale which combines both the ASA speed and the DIN speed in the format ASA/DIN. Using ISO convention film with an ASA speed of 400 would be labeled 400/27°. ASA is by far the more popular of the available standards, especially with newer equipment, and is often used interchangeably with the term ISO, although DIN retains popularity in Germany. The prevalence of ASA is reflected in film packaging which normally boldly states the ASA speed of the film on the box, with the full ISO speed printed in smaller type on the reverse or base. A fourth naming standard is the GOST developed by the Russian standards authority. See the film speed article for a table of conversions between ASA, DIN, and GOST film speeds. Common film speeds include ISO 25, 50, 64, 100, 160, 200, 400, 800, 1600, and 3200. Consumer print films are usually in the ISO 100 to ISO 800 range. Some films, like Kodak's Technical Pan, are not ISO rated and therefore careful examination of the film's properties must be made by the photographer before exposure and development. ISO 25 film is very "slow", as it requires much more exposure to produce a usable image than "fast" ISO 800 film. Films of ISO 800 and greater are thus better suited to low-light situations and action shots (where the short exposure time limits the total light received). The benefit of slower films is that it usually has finer grain and better colour rendition than fast film. Professional photographers usually seek these qualities, and therefore require a tripod to stabilize the camera for a longer exposure. Grain size refers to the size of the silver crystals in the emulsion. The smaller the crystals, the finer the detail in the photo and the slower the film. A film with a particular ISO rating can be pushed to behave like a film with a higher ISO. In order to do this, the film must be developed for a longer amount of time or at a higher temperature than usual. This procedure is usually only performed by photographers who do their own development or professional-level photofinishers. More rarely, a film can be pulled to behave like a "slower" film. History of film Pioneering work on the light sensitivity of films was done by Hurter & Driffield from 1876 onwards; this work enabled the first quantitative measure of film speed to be devised. The first flexible photographic film was made by Eastman Kodak in 1885. This "film" was coated on paper. The first transparent plastic film was produced in 1889. Before this, glass photographic plates were used, which were far more expensive and cumbersome, albeit also of better quality. Early photography in the form of daguerreotypes did not use film at all. The development of digital photography has significantly reduced the use of film. As of 2006, film is disappearing from the consumer market except for low-end disposable cameras in western countries. This is not true of other markets, in particular the asian market where film is still the predominant product over digital. Although many professionals have turned to digital in the past five years, companies such as Kodak and Fuji have recognised that there is a need for transparency film in the pro market and Fuji have maintained that they intend to continue to manufacture transparency film having kept their word by producing new emulsions during 2006. They have recognised that most users of transparency film are owners of high end film SLRs and that many pros prefer a choice for their personal work. The availability of film is also of importance to manufacturers such as Leica, whose film based M series rangefinders have a vast following worldwide. What is likely to happen is that film will be less readily available in western countries. Shops such as Jessops in the UK have run down supplies of transparency film for instance to the point where it can no longer be guaranteed to be stocked in a number of their outlets. This however must be balanced against the growth of internet sales in film where companies such as Mailshots can offer stocks of film for a far lesser cost than most shop based outlets. Special films Instant photography, as popularised by Polaroid, uses a special type of camera and film that automates and integrates development, without the need of further equipment or chemicals. This process is carried out immediately after exposure, as opposed to regular film, which is developed afterwards and requires additional chemicals. See instant film. Specialty films exist for recording non-visible portions of the electromagnetic spectrum. These films are usually designed to record either ultraviolet or infrared light. These films can require special equipment; for example, most photographic lenses are made of glass and will therefore filter out most ultraviolet light. Instead, expensive lenses made of quartz must be used. Infrared films may be shot in standard cameras using an infrared band- or long-pass filter. Exposure and focusing are also difficult when using UV or IR film with a regular camera and lens. The ISO standard for film speed only applies to visible light, so regular light meters are nearly useless. Film manufacturers can supply suggested equivalent film speeds under different conditions, and recommend heavy bracketing. e.g with a certain filter, assume ISO 25 under daylight and ISO 64 under tungsten lighting. This allows a light meter to be used to estimate an exposure. For focusing, the focal point for IR is slightly father away from the camera than visible light, and UV slightly closer. Apochromatic lenses are sometimes recommended due to their improved focusing across the spectrum. Film optimized for sensing X-ray radiation is commonly used for medical imaging, and personal monitoring, and film optimized for sensing gamma rays is sometimes used for radiation dosimetry. Film leaves much to be desired as a scientific detector: it is difficult to calibrate for photometry, it is not re-usable, it requires careful handling (including temperature and humidity control) for best calibration, and it generally requires a physical object (the film itself) to be returned to the laboratory. Nevertheless, photographic film can be made with a higher spatial resolution than any other type of imaging detector, and (because of its logarithmic response to light) has a wider dynamic range than most digital detectors. For example, Agfa 10E56 holographic film has an equivalent resolution of over 4,000 lines/mm -- equivalent to a pixel size of just 0.125 micrometres -- and an active dynamic range of over five orders of magnitude in brightness, compared to typical scientific CCDs that might have ~10 micrometre pixels and a dynamic range of three to four orders of magnitude. Common sizes of film See also Film format. Companies that manufacture photographic film Film manufacturers commonly make film that is branded by other companies. Modern films have bar codes on the edge of the film which can be read by a bar code reader. This is because film is sometimes processed differently according to specifications of the film, determined by its manufacturer; the bar code is entered into the computer printer before the film is printed. To establish the OEM, read the bar code printed on the cassette. Divide the long number by 16 and record the number before the decimal, then multiply the number after the decimal by 16, this could give you a result such as 18 and 2. The first number is known as the PRODUCT (film manufacturer) and the second number as the MULTIPLIER (speed of the film ISO). In the previous example, 18 identifies 3M as the manufacturer and 2 means it is 200 ISO: Notable films See also | ||||||||||
|
| |||||||||||
 |
|
| |