|
"Visible light" is commonly described by its color temperature. A traditional incandescent light source's color temperature is determined by comparing its hue with a theoretical, heated black-body radiator. The lamp's color temperature is the temperature in kelvins at which the heated black-body radiator matches the hue of the lamp. Categorizing different lighting Because it is the standard against which other light sources are compared, the color temperature of a black-body radiator is equal to its surface temperature in kelvin, using the temperature scale named after the 19th-century British physicist William Thomson, 1st Baron Kelvin. (Note: it should not be construed that the color temperature refers to the ''thermal'' temperature of anything other than the black-body radiator.) An incandescent light is very close to being a black-body radiator. However, many other light sources, such as fluorescent lamps, do not emit radiation in the form of a black-body curve, and are assigned what is known as a correlated color temperature (CCT), which is the color temperature of a black body which most closely matches the lamp's perceived color. Because such an approximation is not required for incandescent light, the CCT for an incandescent light is simply its unadjusted kelvin value, derived from the comparison to a heated black-body radiator. As the sun crosses the sky, it may appear to be red, orange, yellow or white depending on its position. The changing colors of the sun over the course of its passage through the sky, is mainly affected by refraction and, to a lesser extent, by the scattering of light, and has nothing to do with black body radiation. Even when the Sun is low over the horizon, we can estimate its apparent color temperature and correct it to compute its effective temperature. So, even if the sun looks red, showing an apparent color temperature of 2500 K, a simple calculation can demostrate that its effective temperature is in reality close to 5770 K. The blue color of the sky is not due to the black body radiation either contrarily to what say some authors but to Rayleigh scattering of the sunlight on the air that tends to spread much more the blue light that the red light, hence the blue color of the sky. This phenomenon has nothing to do with properties of a black body. In addition, the color temperature of the sky cannot be higher to the one of the sun, the main source of light, because the air is in thermodynamic equilibrium In fact the blue sky that we observe in high altitude cannot exceed 6000 K (the effective temperature of the sun, in reality close to 5770 K) because the dark blue color shows a (false) color temperature that should be higher that the one of the black body brought at an infinite temparature ! This is thus a non-sense of speaking of sky color temperature over 6000 K, a rumor based on no physical property. At best, we can speak of brightness temperature of the sky, which is a measurement of its power using a radiometer or a similar instrument. Note this diagram is only a symbolic-representation; the colors shown have not been calculated with any colorimetric accuracy. A colorimetrically-accurate diagram is available here. Some common examples. a candle studio "CP" light ° 5000 K and 6500 K are also called respectively D50 (US standard) and D65 (Europe standard) in all professions working with light (photographers, publishers, etc). It is a temperature similar to the black body temperature but not strictly identical. ¨ the power of a bulb (20 or 100 W) seems to change its color but in reality it only affects its luminosity (luminance) to which our eyes are very sensitive. From these observations, it becomes clear for all colors based on the black body that blue is the "hotter" color, while red is actually the "cooler" color. This is the opposite of the associations both colors have taken on, with "red" as "hot", and "blue" as "cold". The traditional associations come from a variety of sources, such as the fact that water and ice reflect the color of daylight, making them appear blue, and frostbitten flesh often appears blue. Plus, as is well known, metals heated begin to glow red, and fire is reddish. But the redness of these heat sources comes from precisely the fact that red is the coolest of the visible colors: the first color emitted as heat increases. A proof of this is that while incandescent bulbs glow a reddish to yellowish color throughout their lifetimes, when one blows out, the flash of light is noticeably bluish. The filament is hotter when it burns out (as evidenced by the scorch mark often left on the glass). "Color temperature" is sometimes used loosely to mean "white balance" or "white point". Notice that color temperature has only one degree of freedom, whereas white balance has two (R-Y and B-Y). In photography, an alternative numerical measure used is the mired. Color temperatures and mireds are convertible to each other via a simple formula (see the mired page for details of the computations, and the reasons for the use of the alternative unit). Film photography Film sometimes exaggerates the color of the light. An object that appears to the naked eye to be under white light may turn out looking very blue or orange in a photograph. The color balance may need to be corrected while shooting to achieve a neutral color print. Film is made for specific light sources (most commonly daylight film and tungsten film), and used properly, will create a neutral color print. Matching the color sensitivity of the film to the color temperature of the light source is one way to balance color. If tungsten film is used while photographing indoors with incandescent lamps, the yellowish-orange light of the tungsten incandescent bulbs will appear as white (3200 K) in the photograph. Filters on a camera lens, or color gels over the light source(s) may also be used to correct color balance. When shooting with a bluish light (high temperature) source such as an overcast day, in the shade, in window light or if using tungsten film with white or blue light, a yellowish-orange filter will correct this. For shooting with daylight film (calibrated to 5600 K) under warmer (low temperature) light sources such as sunsets, candle light or tungsten lighting, a bluish (e.g. Fluorescent light varies in color and may be harder to correct for. Because it is often greenish, a magenta filter might correct it, though this could take some trial and error. If there is more than one light source with varied color temperatures, gels (placed over each light source) in conjunction with daylight film is the best way to balance the color. Desktop publishing In the desktop publishing industry, it is important to know your monitor’s color temperature. Color matching software, such as ColorSync will measure your monitor's color temperature and then adjust your monitor’s settings accordingly. This enables on-screen color to more closely match printed color. Common monitor color temperatures are as follows: 5000 K (D50), 5500 K (D55), 6500 K (D65), 7500 K (D75) and 9300 K. Designations such as D50 are used to classify color temperatures of light tables and viewing booths. When viewing a color slide at a light table, it is important that the light be balanced properly so the colors are not shifted towards the red or blue. General computer-users should set their PC monitor color-temperature to "sRGB" or "6500 K", as this is what digital cameras, web graphics, and DVDs etc are normally designed for. Indeed the sRGB standard stipulates (among other things) a 6500 K display whitepoint. TV, video, and digital still cameras The NTSC and PAL TV norms call for a compliant TV screen to display an electrically "black-and-white" signal (minimal color saturation) at a color temperature of 6500K. On many actual sets however, especially older and/or cheaper ones, there is a very noticeable deviation from this requirement of the standard. Most video and digital still cameras can adjust for color temperature by zooming into a white or neutral colored object and setting the manual "white balance" (telling the camera "this object is white"); the camera then shows true white as white and adjusts all the other colors accordingly. White-balancing is necessary especially indoors under fluorescent lighting and when moving the camera from one lighting situation to another. The setting called "Auto white balance" is not recommended for optimum quality video or stills. Artistic application via control of color temperature
Correlated color temperature The Kelvin system for lamp description works well for an incandescent light bulb. Since these lamps are very nearly black body radiators, their chromaticity coordinates land directly on the Planckian locus in the CIExy color space. Fluorescent lighting is not incandescent and presents a new challenge. Fluorescent lamps are made using myriad combinations of phosphors and gases. The illumination that they produce is almost never described by a point in color space which lies on the Planckian locus. The question then becomes how to describe the quality of light from a fluorescent lamp. The method used is called the "correlated color temperature", which is a method for assigning a color temperature to a color near, but not on, the Planckian locus. The above plot shows lines crossing the Planckian locus for which the correlated color temperature is the same. Nevertheless, the colors are not the same, and the method gives only an approximate specification of a particular color. Due to this shortcoming, the rated CCT of any fluorescent tube does not completely specify its color. To be more precise: A number of color spaces have been developed in which the difference between two colors may be estimated by the distance between them on a chromaticity diagram. These include the 1960 CIELuv (which is now outdated) and the 1976 CIELu'v' and CIELab spaces. On a chromaticity diagram for which distances specify color distances, the best estimate of the color temperature of any point will be the color temperature of the point on the Planckian locus closest to that point. Although it is outdated, the CIE specifies distances in the 1960 CIELuv chromaticity space to define correlated color temperature. Photographers often use color temperature meters. Color temperature meters by design read only two regions along the visible spectrum (red & blue) or some expensive ones read three regions (red, green & blue). They are almost useless under fluorescent light. There are general guidelines and some specific filters recommended to obtain optimum quality under such frustrating circumstances. Color rendering index The CIE developed a newer model for describing and rating light sources, called the color rendering index, which is a mathematical formula describing how well a light source's illumination of eight sample patches compares to the illumination provided by a reference source. The index provides a number up to 100 for ideal light. This index is useful in determining the suitability of illuminating spaces occupied by humans, since there are adverse health effects of over-illumination by artificial lights or by mismatch of natural light sources. Spectral power distribution plot
Recommendations for those without expensive equipment Only those with expensive spectrophotometers and spectroradiometers can obtain accurate data. Those without these tools should take the time to review the lamp's specifications, and if they seem good, then the eyes are one's best tool. New mathematical indices are being proposed. There are at least 3 new ways to categorize lamps more accurately. They are not in use as of yet. One is referred to as the color rendering capacity (CRC). Film- and video-related See also | |||||||||||
|
| ||||||||||||
 |
|
| |