|
A chain is a unit of length. A chain measures generally between 60 and 100 feet. If not otherwise qualified, the chain as a unit normally refers to the English unit chain, also called a Gunter's chain. This is defined as 66 feet (20.1168 metres). It is also known as the surveyor's chain or land chain.
Conversions of Gunters chain One chain (= 100 links) is equivalent to: Also: Since the width of an acre was defined as one chain (with a length of one furlong), it was also known as an acre's breadth. Gunters chain The term chain derives from the device commonly used for measurement of land in the past — a chain of 100 links, the Gunter's chain (named in honour of Edmund Gunter) being the most common. The links were about eight inches long, made of heavy gauge wire, with a loop at each end. The links were joined end to end to create the chain by three rings between the links. This enabled the chain to be folded up, link by link, until all 100 were in a bundle which could be held in the hand. At each end were brass handles and the full chain measurement was between the outside extremities of the brass handles with the chain at full stretch on flat ground. If the chain had been folded correctly, an experienced chainman (surveyor's assistant) could fling the bundle out and it would unfold neatly with no snags. Another chainman would grab the handle, flick the chain to get it straight and then be ready to take the measurement. Long distances would be measured in bays of one chain, the actual chain being dragged forward for each bay. With so many links in the chain there were many wearing surfaces and chains commonly were longer than the designated length. Also some surveyors added an extra link, so that their surveys always included a greater physical area than the actual measurements indicated (the landowners weren't going to complain!). When retracing old surveys with modern equipment a surveyor will almost always find his measurements between monuments are longer than the originals. The unit was once important in everyday life, being one of the fundamental units of Imperial system in the United Kingdom and its colonies, and was used to some extent in engineering and surveying in the U.S. In Britain, it was commonly used in the railway industry (where the measure is still in widespread use). Mapping by the Ordnance Survey (Britain's national mapping organisation) began in the early 19th century using the chain as the basic unit of measurement. All map scales at that time were expressed as a relative fraction of a chain or a mile (e.g. a one inch to ten chain scale was equivalent to 1:7920 or eight inches to a mile). The use of the chain was once very common in laying out townships and mapping the U.S. along the train routes in the 19th century. In the U.S. a federal law was passed in 1785 (the Public Land Survey Ordinance) that all official government surveys must be done with a Gunter's chain (also referred to as the "surveyor's chain"). In Australia and New Zealand, most building lots in the past were a quarter of an acre, measuring one chain by two and a half chains, and other lots would be multiples or fractions of a chain. The city of Melbourne is a classic example: surveyor Robert Hoddle divided the city into 24 ten-chain blocks, which still serve as the basic grid of the city. The street frontages of many houses in these countries are one chain wide—roads were almost always one chain wide (20.117 m) in urban areas, sometimes one and a half or two chains (30.2 m or 40.2 m). Laneways would be half a chain (10.1 m). In rural areas the roads were wider, up to 10 chains (201 m) where a stock route was required. Ramsdens chain American surveyors sometimes used a longer chain of 100 feet (30.48 m), known as the engineer's chain or Ramsden's chain. Hispanic chain In Texas, the vara chain of 20 varas (60 Mexican feet) was used in surveying Spanish land grants. Conversion: . Contemporary use In agriculture, measuring wheels with a circumference of 0.1 chain are still common and readily available in the United States and Canada, at least. For a rectangular tract, multiply the number of turns of one of these wheels for each of two adjacent sides, then divide by 1000 to get the area in acres. The chain also survives — in fact, if not always in name — in two other specific contexts. | ||||||||
|
| |||||||||
 |
|
| |